Item no.: 12242V2
- Description
- Manuals
- Information ElectroG3
![](absima_en/prodpic/galerie/12242v2_snow1.jpg)
![](absima_en/prodpic/galerie/ab3.4blheader.jpg)
![](absima_en/prodpic/galerie/abs12242v2_4.jpg)
The success story continues! We have equipped the AB3.4 "V2" brushless with some new features that bring the vehicle to the next level of evolution.
![](absima_en/prodpic/galerie/12242v2_01kopie.jpg)
![](absima_en/prodpic/galerie/12242v2_02kopie.jpg)
Some technical changes have been implemented in our 1/10th scale buggy - among other things, the vehicle now comes with LED lighting on the roof
![](absima_en/prodpic/galerie/12242v2_05.jpg)
![](absima_en/prodpic/galerie/highlights-blue-orange.jpg)
- NEW* 60A brushless speed controller withT-connector and 3421KV motor
- NEW* Programmable speed controller
- NEW* 6kg steering servo
- NEW* LED lighting
- NEW* Downforce rear wing
- NEW* even more option parts available
![](absima_en/prodpic/galerie/features-blue-orange.jpg)
![](absima_en/prodpic/galerie/abs12242v2_7.jpg)
The new 60A brushless speed controller is waterproof, programmable and pre-configured with a T-connector. To fully exploit the potential of the vehicle, we recommend a 2S/7.4V LiPo battery for operation. In addition, a separately available programming box (item 2110062) can be used to set various parameters such as braking force, punch, low voltage protection and more.
![](absima_en/prodpic/galerie/1-10-brushless-set-thrust-bl-ecov2-60a-3421kv-2120002v2_b_0.jpg)
![](absima_en/prodpic/galerie/unknown-1.jpeg)
The car is powered by a 3421KV brushless motor that directly accesses the all-wheel drive. The two differentials (front and rear) are driven by an aluminum driveshaft. A 6kg servo handles the conversion of the steering commands. The motor/controller unit can also be powered by a 3S/11.1V LiPo battery (note the size of the battery compartment!), but this increases the wear and tear on the vehicle extremely. Also the handling becomes almost impossible due to the enormous over-motorization. Therefore, we generally advise against 3S driving.
4 adjustable aluminum oil-pressure shock absorbers offer ideal handling, so that a lot of driving fun. The spring preload can be adjusted via a knurled screw. Thus, the chassis can be perfectly adapted to your needs.
![](absima_en/prodpic/galerie/12222v2_10kopie.jpg)
![](absima_en/prodpic/galerie/12222v2_11kopie.jpg)
Lightweight and compact design, as well as comfortable and ergonomically shaped - these are just two features of our CR4S 4-channel remote control. Of course, all trim, reverse and dual rate functions are available in the cockpit, making adjustments easy via levers and knobs. In addition, the remote control has a "Beginner Mode" (speed reduction by 50%) and is therefore ideal for pilots who do not yet have so much experience with the handling of such RC vehicles.
![](absima_en/prodpic/galerie/unknown2.jpeg)
![](absima_en/prodpic/galerie/unknown3.jpeg)
- 4WD all wheel drive
- 2.4GHz 4-channel radio system
- 60A brushless speed controller (waterproof; T-plug; programmable)
- 3421KV brushless motor (sensorless; splash-proof)
-
6kg steering servo (25T, ball bearings)
-
Aluminum oil shock absorbers
- Ball bearing main drive
-
Extremely durable composite plastic parts
-
Steel differential outdrives
-
Aluminum main drive shaft with steel mounts
-
Adjustable upper tie rods
-
5mm aluminum motor mount
-
6mm shock towers
-
2 differentials (front/rear)
-
Stylish "Cap Forward" buggy body
-
"Light-Weight" chassis (less weight - longer drive time)
- Many aluminum option parts available
![](absima_en/prodpic/galerie/tecspec-blue-orange.jpg)
-
Scale: 1:10
-
Dimensions (L/W/H): 380x255x155 mm
- Weight: 1530g
- Wheelbase: 270mm
-
Ground clearance: ca. 30mm
-
Track width: 215mm front/rear
- Front wheels: Ø 88mm / Width: 33mm
-
Rear wheels: Ø 88mm / Width: 42mm
- Shock absorber oil: 400CPS
- Shock absorber installation length: 90mm
- Motor ratio: pinion 26T / main gear 64T (module 0,6)
![](absima_en/prodpic/galerie/delivery-blue-orange.jpg)
![](absima_en/prodpic/galerie/12242v2_11.jpg)
- 1/10 Brushless Buggy "AB3.4BLV2" RTR
- 2.4GHz "CR4S" radio
- Sticker sheet
- Manual
![](absima_en/prodpic/galerie/accessories-blue-orange.jpg)
- 4x AA Batteries for radio
- 7.4V/2S* LiPo car battery (*recommended)
- Charger (suitable for car battery)
- Programm box for individual settings of the speed controller
![](absima_en/prodpic/galerie/12222v2_12242v2_a04.jpg)
![](absima_en/prodpic/galerie/12222v2_12242v2_a05.jpg)
![](absima_en/prodpic/galerie/12222v2_12242v2_a06.jpg)
Spare Parts for this item:
Option part for this item:
Average customer rating:
Number of Customer reviews: 0